![]() ![]() ![]() ![]() You have to call and the guy has to go look in the back for anything. No website, no computerized anything, and they prefer cash. Again, if you are in So Cal and need specialty hardware for automotive, firearms, aircraft, etc., King Bolt in Covina has a lot. These worked great, though, and there was no wait. If I wanted to wait a few days, I could have gotten them from Amazon for less. I bought some nice ones at a local specialty hardware store. HF does not carry additional inserts and they are not really easy to find at a brick and mortar. Also, the fix is as simple as a washer and it works well with that in place. I would still recommend this tool, however, as it is much less expensive than other ones I looked at that appear to be the same re-branded tool. The design ought to be better as that would seem like an easy problem to remedy. The Threaded insert riveter had a nice feel and appeared to be of good quality, however, it required a washer underneath the nose piece to pull the insert tight in sheet metal. everything seems to be snapped or popped together today, so I'm sure I will get more use out of this tool. ![]() I used the factory rivets I bought for re-installation, however, the ones that came with the tool looked to be good quality. It came with an assortment of POM rivets, and HF carries more. The tool quality was very good, it was inexpensive, and did the job right each time I used it. There isn't really any ugly in this case, but I will go to the good, real good in this case, first. I used the premuium Line-X that is UV resistant. He did a great job and charged me less than the local guy we have. If you are in Southern California and need Line-X work, I would certainly recommend Pasadena Line-X. The guy I had do the Line-X was familliar with coating the Jeep fenders and did a great job pushing through all the holes I needed to use for remounting the fenders. They also let the fender rattle a little, so they were not a great method to begin with. The clips were going to be very difficult, and likely impossible to use. When you Line-X plastic fenders, they have to be encapsulated, making them thicker. Instead, I used the rivnut tool to put 1/4-20 inserts into the body and reinstall the fenders with bolts rather than clips. The fender itself is held by a series of pop-in clips that I was no longer going to use. When you pull them there are a number of POM rivets that hold the liner on that have to be replaced. I pulled the fenders and had them Line-X coated as part of a refresh project on my wife's 2007 JK Sahara Unlimited. With this full kit we do our very best to package perfectly for our Vicrez Customers.A threaded insert riveter kit #1210 (21.99) and a Poly hand riveter kit 97757 (16.99) for a project on my wife's JK. The tool can be used on alluminum, plastic and metal. For easy storage, portable use and travel all of our tools and accessories are packed in a plastic case with an anti slip carrying handle and dual lock clips for safety. - The kit (#vzt109) is designed with mandrel knob's to separate the rivet nut easily from the gun after it has been fixed our tool even limits the opening of handles after the nut has expanded to prevent it's thread from deformation.The Vicrez Rivet Nut tool kit has various uses outside of wickerbills and fender flare installation but can also be used at home for furniture repair, decoration, cars, trailers, even boat building and to top it off our kit is easily operable. - Our new Complete Rivet Nut tool is brought to you from the vicrez team to meet all your needs with high quality threaded mandrels with nosepieces: 6-32, 8-32, 10-24 and 1/4-20, our full kit has 45 pieces of Ribbed Rivnuts, 10 each 6-32, 8-32, 10-24 and 1/4-20.Subscribe: New Vicrez videos daily! Subscribe to our YouTube Channel ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |